MAS PUMPS was founded in 1977. Ever since MAS’ s beginning as a manufacturer of pumps in Turkey over 25 years ago, we have dedicated ourselves to the efficient use water and the preservation of a proper environmental balance much more than merely a manufactuer, MAS is today also a comprehensive engineering firm active in research and development of products and accessories for the efficient control and operation of facilities.
END-SUCTION CENTRIFUGAL PUMP (NM)
Capacity : up to 3500 m3/hr Head : up to 105 m Operating Pressure : up to 10 (16) bar Temperature : up to 90 c (140 c)
NM single stage, end-suction centrifugal pump according to DIN 24255 standard. In addition to 25 basic sizes conforming NORM there are 17 additional sizes. Single entry, closed impeller is hydraulically thrust compensated and dynamically balanced.
HORIZONTAL SPLIT CASE PUMPS (SPLT)
Capacity : up to 4,000 m3/hr Head : up to 160 m Operating Pressure : up to 16-20 bar Speed Range : 960 to 3600 rpm
SPLT Single or double stage, axially split casing pumps with double entry, radial impeller. Bigger size are double volute construction. Double entry, closed impeller is hydraulically thrust compensated. Lower casing is in-line design, suction and discharge nozzle are on the same line. Upper casing self-aligning and therefore easy to mount
HOT OIL PUMPS (KYP)
Capacity : up to 300 m3/hr Head : up to 90 m Operating Pressure : up to 16 bar Temperature : up to 350 c
KYP Horizontal single stage centrifugal pumps specially designed for pumping the thermal fluids at a high temperature, in industrial installations without needing any type of external refrigeration.
The hydrulic characteristic of pumps are in accordance with the standard DIN24256(ISO 2858) for chemical pumps. Which means that for each installation the most suitable pump can be used to give optimum performance.
INLINE PUMPS (INM)
Capacity : up to 700 m3/hr Total Head : up to 100 m Operating Pressure : up to 10 (16) bar Temperature : up to 90 c (140 c)
INM pumps are single stage, centrifugal pump of non self-priming type fitted with standard motors and mechanical shaft seal. Norminal flowrate of pumps comply with En733 standards. Pump flanges sizes according to DIN 2533,PN 16. The dimension of suction and discharge ports are indentical
HORIZONTAL MULTISTAGE PUMPS (KMU)
Capacity : up to 16 m3/hr Total Head : up to 250 m Operating Pressure : up to 25 bar Temperature : up to 90 c (140 c)
KMU is a horizontal multistage pump non-self priming type centrifugal pump. Impellers are between bearing single entry, closed type and dynamically balanced. Pump and motor are fitted on a common baseplate connected to each other by a flexible coupling. As standard version discharge port is at motor side on top and suction port is at dead end side on left. Suction and discharge port are rotatable by 90
HIGH PRESSURE MULTISTAGE PUMPS (KMB)
Capacity : up to 100 m3/hr Total Head : up to 300 m Operating Pressure : up to 40 bar Temperature : up to 90 c (140 c)
KMB pump is a horizontal axis, radially split, ring section design multistage centrifugal pump of self-priming type. Impellers are between bearing, single entry, closed type, and dynamically balanced. For balancing the axial thrust, all impellers have back wear rings. It is not necessary to use balancing disk or drum. Pump and motor are fitted on a common baseplate connected to each other by a flexible coupling.
HIGH PRESSURE OPPOSED IMPELLER MULTISTAGE PUMPS (KMK)
Capacity : up to 130 m3/hr Total Head : up to 600 m Operating Pressure : up to 40 (64) bar Temperature : up to 90 c (140 c)
KMK is a horizontal axis, radially split, ring section design multistage centrifugal pump with opposed (back to back) impellers. Impeller are between bearings, single entry, closed type and dynamically balanced. Axial thrust automatically balanced thanks to opposed impellers. It is not necessary to use balancing disk or drum. Pump and motor are fitted on a common baseplate connected to each other by a flexible coupling.
HIGH PRESSURE MULTISTAGE PUMPS (KME)
Capacity : up to 800 m3/hr Total Head : up to 500 m Operating Pressure : up to 50 bar Temperature : up to 90 c (140 c)
KME pump is a horizontal axis, radially split, ring section design multistage centrifugal pump of non self-priming type. Impellers are between bearing, single entry, closed type, and dynamically balanced. For balancing the axial thrust, all impellers have back wear rings. It is not necessary to use balancing disk or drum. Pump and motor are fitted on a common baseplate connected to each other by a flexible coupling.
